bandeira bandeira
Detalhes do blog
Created with Pixso. Casa Created with Pixso. Blogue Created with Pixso.

Facial Tissue Production Line for Middle East Mills: Capacity, Voltage and Climate Guide

Facial Tissue Production Line for Middle East Mills: Capacity, Voltage and Climate Guide

2026-10-27

Facial Tissue Production Line for Middle East Mills: Capacity, Voltage and Climate Guide

Why facial tissue converting capacity is being added across the Gulf and North Africa

Facial tissue has become one of the fastest moving paper categories in the Middle East. National localization programmes in Saudi Arabia and the UAE, a hospitality pipeline that keeps adding hotel rooms in Riyadh, Jeddah, Dubai and Doha, and steady growth in household hygiene spending have pushed retailers to look for regional supply instead of container imports. For a converter, the practical question is no longer whether a facial tissue production line makes sense, but which configuration survives a 50 °C summer, a 380 V/50 Hz grid and a service network that sits four time zones away.

What a complete facial tissue production line actually contains

A facial tissue production line is a chain of machines, and each link sets the ceiling for the ones behind it. The table below shows the modules a converter normally installs for 2–3 ply V fold facial tissue.

ModuleTypical specificationWhat it controls
Unwinding stands1–5 units, 2100 mm parent roll widthPly count and paper splicing downtime
V fold folding machine100–130 m/min, 200 mm or 210 mm folded sizeOutput speed and interfold accuracy
Log saw200–360 cuts/min, 500–610 mm round knifeCut accuracy and knife cost per tonne
Soft pack packing machine140–160 packs/min, PE or BOPP filmRetail pack quality and film consumption
Bundle or carton packing10–15 bundles/min, pre-made bag or heat sealPallet presentation and distributor acceptance
Optional embossing and printingSteel to rubber or steel to steel, 2–4 colour flexoPrivate label value and shelf differentiation

The folding machine usually decides the line rating. A 130 m/min V fold head converts to roughly 100–140 retail packs per minute depending on sheet count and ply, and the packing machine must be sized above that figure so the folder never waits.

Five Middle East adaptations that decide whether the line runs smoothly

1. Voltage and frequency, confirmed at the nameplate

Most Gulf industrial parks run 400 V/50 Hz three phase, Saudi plants commonly 380 V/50 Hz, and some older facilities still distribute 220 V. Confirm the plant voltage before the order is released, not after the container arrives. Motors and inverters must be rated for the local grid, and insulation should be Class F or H rather than the Class B specification often quoted for temperate markets.

2. Ambient temperature and control cabinet cooling

A converting hall in Riyadh or Jeddah can sit above 45 °C for weeks. Hydraulic power units need an oversized oil cooler, control cabinets need dedicated air conditioning, and high temperature grease is mandatory on folding head and log saw bearings. Specify the ambient design temperature in the purchase contract so the supplier derates motors rather than discovering the problem in July.

3. Dust, sand and filtration

Fine sand finds every unsealed bearing and photoelectric sensor. Sealed bearing housings, filter mats on cabinet intakes and a documented weekly cleaning routine add little to the price but visibly extend sensor and knife life. Ask for the filter specification in writing.

4. Water and steam quality

Where embossing lamination or steam heated drying is used, hard water scales heat exchangers within months. A small reverse osmosis unit ahead of the boiler is the cheapest reliability upgrade most Middle East converters can make. Conductivity and hardness targets should be part of the commissioning checklist.

5. Spare parts and service response

Downtime cost in a two shift plant is measured in tonnes. A realistic agreement covers a regional parts stock holding knives, belts, sealing bars and sensors, remote diagnostic support across time zones, and a stated engineer deployment window including visa processing time. Commissioning for a full facial tissue production line typically needs 7–10 days on site with operator training included.

Capacity planning example

Take a line built around a 130 m/min V fold folding machine running 2 ply, 16 gsm paper with 200 mm folded size and 150 sheets per pack. At a realistic overall equipment effectiveness of 70 %, the line produces roughly 5,500 to 6,000 retail packs per hour. A single shift covers domestic retail programmes; a second shift is normally justified once a private label contract exceeds 15 containers per year. Because the numbers swing widely with sheet count, ply and pack format, always ask for a capacity curve tied to your own SKU list rather than a headline speed figure.

Supplier checklist before signing

  • Line layout drawing matched to your hall dimensions, door widths and container unloading path
  • Written voltage, frequency and ambient temperature specification on the nameplate drawing
  • Named reference plants in the region that can be visited or called
  • Spare parts price list for year one and a stated regional stock location
  • Certification package for customs clearance, including conformity documents for the destination market

Next step

If you are evaluating a facial tissue production line for a Middle East project, send us your target capacity, pack format and plant voltage. We will return a line configuration, layout drawing and itemized quotation, plus the climate adaptation list for your specific site. Machines ship in export grade wooden cases with English manuals, and our engineers support installation and operator training on site.